Junked 1990 Volvo 740 GL with Cerma Engine Treatment

Came in 2nd place in the Terryville Fair Demolition Derby (2015).   From James McGrath:  www.CermaLube.com  (203) 376-1152

EVIDENCE of Efficacy... usher the new technology in!   From Veloster Forum and Senior Member, Peter K.  Indianapolis.

OLD technology (non cerma motor oil) uses detergents, and attempts to keep carbon in solution (emulsified). This suspended carbon is way too small to be harvested by even the best of over the counter oil filters -- any brand. None of them filter finer than 40-45 microns.

Cerma Attends Auto Fest with Josh Borne


Josh Borne is a championship freestyle competition performer, a premier professional freestyle extreme athlete, and a world renowned competitor on the XDL Championship Sportbike Freestyle Series and multiple other circuits.  Borne has traveled across the nation and around the globe showcasing his high energy talents to crowds of all ages.

Cerma Attends 2015 NYC Fleet and Equipment Show at the Unisphere...
Cerma STM-3, while extending oil drain intervals, continues to provide protection...
To fix this common problem and reduce the noise caused by issues with the lifters...
If engine is losing oil and the engine is not broken, the motor oil is not doing it job in this "closed" system...
Cerma STM-3 Fuel Treatment Promotion.  Increase Power, Improve Performance...
Protects like a 40W, runs like a 0W.  Cerma Releases EVO Motor Oil, the most advanced motor oil on the market today...
In a perfect world, facilities would operate the same vehicles, of the same age, under the same operating conditions...
99 miles on the engine treatment, less engine noise, quieted the hpfp...
Can be used in all 4-stroke motorcycle engines, including racing, high performance, street, and off road motorcycles...
Government mandated reductions on Zinc and Calcium levels in motor oils has gradually removed...
Due to deteriorating piston seal o-rings, vanos units have been consistently diagnosed...
Veloster Forum, 205 pages and counting, all the information you need and then some...
Cerma CSL Firearm Foam and Grease,  Improved formula with STM-3 Technology


Re-post from:http://www.velosterturbo.org/forum/veloster-maintenance/5282-cerma-treatments-oil-lubricants-good-order-222.html#post353642
02-23-2016, 10:09 Read more

Sly4c Thursday, March 10, 2016
40 FT Meridian Yacht

The boat is going over 28 MPH. Granted clean bottom and props but I don’t believe it ever went over 26ish on this boat. It is a 40 FT Meridian Yacht weighing Read more

Leigh Overland 40 FT Meridian Yacht Wednesday, June 4, 2014
Honda 1300 Shadow

I am the guy who spoke with you at length and purchased some fuel treatment, oil additive and gun lube. I put the fuel and oil additives in immediately. Read more

Kurt P. Honda 1300 Shadow Friday, June 24, 2016
16” AR-15

I must admit that I tend to view products with skepticism however the proof was in the data. I saw a legitimate 200 fps gain in a 16” AR-15 that would Read more

Corey Vento- Police training officer Norwalk CT Police Department Tuesday, May 7, 2013

Before using Cerma, this car, a work car with 160K miles, would jerk every time it changed gears when you drive and the water temperature would be pointed Read more

Tuan H. 2002 Honda Accord EX V6 Tuesday, July 19, 2016
1996 Toyota Camry

TRY THIS IN YOUR ENGINE.........I was amazed, within 15 mins how better my engine sounded and now my car rides as good as ever........Cerma is awesome. Read more

Eric Dobbie '96 Toyota Camry Tuesday, July 22, 2014
Ken's Automotive Services

Cerma lubrication is an advanced metal treatment that works great to reduce heat and friction in engines , drive trains and A/C compressors. The engines, Read more

Ken Faurot Owner: Ken's Automotive Services Wednesday, March 7, 2012
Dodge Ram 250

Dear Cerma, I started using your products in the summer of 2013. I travel all over the country in my 1991 Dodge D250 two wheel drive with a 5.9 L Cummins Read more

Tom C. Dodge Ram 250 Monday, October 26, 2015

Hi John. I decided to try Cerma and my first use was in my daughter's 2002 Mazda Tribute with about 100,000 kms on it. It was running a bit rough and Read more

Tom D. 2002 Mazda Tribute Tuesday, February 18, 2014
2002 Toyota Sienna Minivan

I used Cerma STM-3 Engine Treatment in my 2002 Toyota Sienna Minivan; Fuel mileage went up from 260 mile per tank to 355 miles extremely happy with gas Read more

OKTAY TUZER 2002 Toyota Sienna Minivan Wednesday, March 7, 2012

In my application, 1991 BMW 750i 5.0L 12 cylinder, I was mainly trying to correct annoying hydraulic lifter noise without having to replace any lifters. Read more

Mark C. McCafferty, P.E. 1991 BMW 750i 5.0L 12 cylinder Tuesday, February 18, 2014

So...I just got the oil changed to Cerma 5W30 and could feel a huge difference just starting the car up. Engine vibration in the pedal has gone almost Read more

CH3mist - Veloster Forum Member Hyundai Veloster Saturday, February 1, 2014
Subaru Legacy 1997 Wagon

I have purchased 2oz of CERMA engine treatment with STM-3 and got a free 2oz of Fuel Treatment. Thank you for the gift! Vehicle is: Subaru Legacy 1997 Read more

Ivo K. Subaru Legacy 1997 Wagon Tuesday, September 1, 2015

CERMA is the real deal! If you follow the instructions after applying product to your oil, you will notice less noise, better fuel economy, about 1.5 Read more

ReachMe Happy Customer Sunday, September 28, 2014
Cerma Attends Auto Fest with Josh Borne

For a freestyle stunt rider, "heat is the biggest problem for bikes”. "Took me some time to test the product in the Kawasaki, but finally was able to Read more

Josh Borne - Professional Freestyle Extreme Athlete Cerma Attends Auto Fest with Josh Borne Monday, November 30, 2015
2015 Volvo Day Cab

I just wanted to tell you about my Volvo semi that I drive. It is a 2015 Volvo Day Cab with A/T. It now has 39,500 miles on it. I treated it at about Read more

Chad S. 2015 Volvo Day Cab with A/T Tuesday, September 29, 2015
Mercedes Benz '91 560 SEC


I heard about Cerma oil treatment from a friend who had amazing results with a sluggish high-mile Acura minivan. I treated Read more

Patrick M. Mercedes Benz '91 560 SEC Monday, April 6, 2015

CERMA changed my old engine with 225,000 miles to a NEW engine with a power never seen. When I received the package, i opened it and i was suprised seeing Read more

Zerocool Montero Sport 1998 ES I4 2.4L Monday, January 5, 2015
BMW 318i

Hi everyone!

This post is a "give back" I hope to help a few with this one, as so many helped me with replies on my first post. I learned much. At Read more

Mike Wentz '83 BMW 318i Friday, August 7, 2009

Thanks for the emails, i am getting better gas millage in my bike, was at 39 MPG. I am now getting 43 MPG after 300 miles of riding on Cerma! --Greg J. Read more

Greg J. Saturday, June 25, 2016
Alliant Energy

We have used Cerma in a gear box which is 1 of 2 identical units. The one
we treated was initially running 60 decrees hotter than the other one. We want Read more

Eric Krahenbuhl Alliant Energy, Emery Generating Station Monday, July 16, 2012

My fiat now runs like a 6cyl. Boy has it got power. It now beats lots of 6cyl. I did my engine using EVO oil and fuel treatment. -- Bill D.

Bill Diel Fiat 500 Sport Monday, January 11, 2016

Well its finally complete,.. my VT has been engine treated, 6000 mi. ran in, and turbo treated, 6500 miles ran in. 7500 mi. can around, the "carrier" Motul Read more

Peter K. (aka Gaijii) From Veloster Forum -- CERMA Treatments/Oil/Lubricants: For the good of the order Saturday, December 28, 2013
Mitsubishi Challenger

Hullo John,
I bought 1 bottle of Cerma STM-3 Engine Treatment and 1 bottle of Cerma STM-3 Automatic Transmission Treatment from you in May 2008. I treated Read more

J Wulf Mitsubishi Challenger Sunday, February 8, 2009
Chevy Camarom RS

I put it in the engine oil and transmission. Transmission stopped slipping on very first drive home from work. I could not believe it!

Anonymous 1991 Chevy Camarom RS with 213,000 miles on it Saturday, July 31, 2010

My name is ECS, i was introduced to your product by a friend. I spoke with John your technical analyst and asked him if this would be a good product for Read more

Ernest Strong VW Tuesday, December 6, 2011
.357 Sig Semi

I used the Cerma foam treatment in the following handguns: .44 revolver, .357 revolver.40 semi, .357 sig semi and AR 15 .223 rifle so far. I am very pleased Read more

Dale W. .44 revolver, .357 revolver.40 semi, .357 sig semi and AR 15 .223 rifle Wednesday, October 7, 2015
  • Cerma STM-3
    Technology and

    Learn More
  • Cerma Motor Oil
    Technology and

    Learn More
  • Cerma Blue Ice
    Technology and

    Learn More